Just how to Replace a Bath Tub ( Guide).
Just how to Replace a Bath Tub ( Guide).
Blog Article
Here in the next paragraph you can discover additional sound tips on the subject of How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old tub with a new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the job can relocate immediately; if you have to open up a wall surface to remove the old bathtub as well as place the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will assist you mount a new bath tub in your bathroom if you have actually already gotten a brand-new tub and also don't need to transform the arrangement of your previous water pipes.
Your tools and also material list should make up the following:
Planning for the Installation
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub up until the level checks out level.
To mount taps, fit all-time low of the furthest versatile tap adapter to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the water supply and also check all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area between the tap and the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are marketed in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealer can split relatively early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that portion was appropriate. You should set aside a second to promote this entry if you appreciated it. Thanks a lot for going through it.
Schedule Today Report this page